The AML Advanced Multifunction Logger has been designed with electronics divided into a module that manages power and communication and a module that manages measurements and recording of data. It is a platform which allows new instruments and devices to be quickly developed on top of proven infrastructure.
AML Advanced Multi-Function Logger
|Internal Battery Specifications|
|4.8Ah Lithium Polymer, 4.20 Volts fully charged|
|External Power Requirements|
|Bus Power||8-30 Volts DC, non-polarised, current draw is 340mA maximum at 17 volts per logger|
|USB Power||5 Volts DC|
|Internal Charge Rate|
|Bus Power||60mA – 700mA Variable internal charge rate, maximum charge rate of 700mA active when the external voltage rises above 16 Volts DC|
|USB Power||100mA fixed charge rate|
|Internal Power Management|
|Fully Charged Battery||4.20 Volts|
|Low Power Mode||3.60 Volts – Instrument ceases to take measurements|
|Discharged Battery||2.90 Volts – Instrument automatically switches off at and below this voltage when no external power connected.|
|Battery Life varies|
ICT environmental systems have been designed to provide seamless solutions from the measurement point to wherever the data is needed, whether directly to a SCADA or PLC system, via Modbus, or to a mobile phone or iPad via the internet.
An extensive range of precision sensors, instruments and data loggers is complemented by a comprehensive suite of communications solutions and software providing system and data management, viewing and analysis.
Equipment installed on site can be automatically discovered and added to the network.
The ICT AML (Advanced Multifunction Logger) is capable of performing a broad range of analogue and pulse / counter type measurements. It has 10 analogue inputs (10 single ended, or 5 differential), 2 pulse inputs, as well as RS485, SDI12, i2c, USB and 2.4GHz wireless interfaces. It can record up to 64 separate channels with 24bit precision. It also monitors and records its own power supply voltages and currents, temperature, air pressure and wireless signal strength.
In order to streamline the application of the AML, ICT can provide application specific distribution boards that target a known set of sensors. The AML automatically recognises the distribution board and configures the inputs and internal logging to suit. If a different type of distribution board is plugged in, the AML configuration will again change. This allows a very wide range of sensor types and signal levels to be interfaced to the AML. The AML does NOT require user programming or knowledge of programming languages to configure it to start logging.
Virtual channels, allowing scripts to be entered, provide mathematical and logical functions. Inbuilt functions such as Evapotranspiration calculation based on the Pennman-Monteith equation, VPD calculation, and Correction of barometric pressure for altitude are standard.
Each channel can produce an alarm based on a user configurable condition.
Each channel can be logged at a different interval, from 1 second to 1 hour + up to 3 user entered schedules
All data recorded by the AML is stored on a MicroSD Memory card in .CSV files. Maximum card size is 32GB. The MicroSD card is formatted as FAT32. The AML is able to communicate with the ICT MCC Hub via 2.4GHz low power radio with CSV files from the AML synchronised with CSV files in the MCC Hub. The MCC Hub can receive data from a network of AMLs and other MCC Hubs. An MCC Hub can be, additionally, fitted with a 3G, Wi-Fi or Bluetooth modem to allow it to send data to the internet and for configuration information to be downloaded to the MCC Hub and then sent to AMLs.
The MCC Hub has an optically isolated RS485 port that can be configured for the Monibus protocol to interface with a range of PLCs and SCADA systems.
The ICT AML and the MCC Hub are both powered by wide temperature range Lithium Ion batteries. The AML can run in full power mode, constantly taking measurements, for use with control systems, or in power saving mode where it is asleep between measurements.
The ICT AML and the MCC Hub can also be powered from mains by a 24V wall charger or a solar panel in remote applications. The AML has a 10-30 Volt DC power input for direct connection to a solar panel.
The AML standard enclosure is IP67. The standard MCC Hub enclosure is IP65.
Note: The sensors will output in units of physical values, kPa in this instance, as the calibration function is entered into the AML.